79° Muzzle Crowning Cutter Brownells
79° Muzzle Crowning Cutter Brownells.
Product Description
Cuts Popular "11\" Target Crown
Hardened steel, muzzle crowning tool cuts a slight (11° less than square) target chamfer on barrels. Gives good rifling protection without going too deep. 90° - 11° = 79°, hence the name. Eight, precision-machined flutes give smooth, chatter-free cuts to help eliminate extra lapping or stoning. ¼"-20 thread fits Brownells muzzle chamfering handles. Use with our muzzle pilots to ensure precise alignment with your bore. Available in ½" and ¾" diameters to accommodate most rifle/handgun barrel diameters.
Big Book Catalog, Issue:71, Page:457
SPECS: Tool Steel, 23/8” (6cm) overall length, ½" (1.3cm) or ¾" (1.9cm) O.D. ¼"-20 tpi.
Brass One Caliber Set Brownells.
Product Description
Square Up & Chamfer Rifle and Handgun Muzzles P Brass Bore Pilot
Set includes: one, 90° facing cutter to square a muzzle after shortening, or repair damage; one, 45° chamfering cutter to break the edges of the rifling for a clean bullet exit or chamfer a revolver cylinder mouth for quick reloads; plus one handle that fits either cutter and one brass bore pilot. Interchangeable pilot keeps cutter properly aligned. Purchase extra pilots to use one cutter for many different calibers. Pilots for other calibers available separately.
Select one of the following for other rifle/handgun muzzles, cylinder facing & chamfering tools.
Chamfering & Facing Combo Sets | 45° Cutter & Steel Pilot | ||
Steel One Caliber Set | 45° Cutter & Brass Pilot | ||
90° Cutter & Steel Pilot | Steel Pilot Only | ||
90° Cutter & Brass Pilot | Brass Pilot Only |
Big Book Catalog, Issue:71, Page:458
Rimmed & Belted Rifle Chambering Reamers Clymer.
Product Description
Finest Workmanship & Quality; Made In USA From M-7 High Speed Steel
Made by Clymer, a truly dedicated group of gun people, from best quality, M-7 High-Speed Steel. These are precision tools for the professional gunsmith and will give a lifetime of service when properly cared for. Fully guaranteed. Roughers are .010" smaller in diameter than the final size, do not cut the throat area and should be used to save wear on the Finish Reamer when many chambers are to be cut. If only a few chambers will be cut, a Finish Reamer is all you need. Superb quality reamers made to SAAMI specifications.
Note: If you do not see the caliber you are looking for below, please feel free to contact our Special Orders Department, as many additional items are avaliable from Clymer.
Big Book Catalog, Issue:71, Page:454
SPECS: RIFLE REAMERS - 6, right-hand cutting, straight flutes. Solid pilot, integral throat. Stocked in Rougher and Finisher. 7/16" round shank with 3/8" square drive. ¼" round shank on .22 RF. ORDERING: Advise: 1) Stock #. 2) Cartridge Caliber and Name.
Pull Through Chamber Reamers Clymer.
Product Description
Create Super-Accurate Minimum Headspace Chambers On .30 Caliber Match Rifles
The same special reamers military armorers have long used to cut minimum length chambers on match rifles, giving their shooters the accuracy advantage. The gun's own bolt applies pressure to the reamer while reamer is turned from the muzzle end. When the bolt "drops", the chamber is cut. Improved design cuts the shoulder, neck and throat to prevent neck crimping of the ammo. Use as a finish reamer ONLY. Cut chamber with conventional finish reamer first. Superb quality reamers made to SAAMI specifications.
Big Book Catalog, Issue:71, Page:454
SPECS: .308 & .30-06 Reamer Sets include: Pull Through (P/T) Reamer, Thrust Bushing and Extension Shaft. Shaft - 24" (60cm) long, ¼" (6.3mm) diameter, round shank. Use #184-054-653 Throater/.22 T-Handle to drive shaft. Reamers work on bolt action or semi-auto rifles.
Chamfering & Facing Combo Sets Brownells.
Product Description
RIFLE SET - Includes one 90°, 45°, and 79° Cutter, plus one Handle and all Rifle Pilots. Flip-storage box with foam insert. Does not include .17 caliber pilots. HANDGUN SET - Includes one 90°, 45°, and 79° Cutter, plus one Handle, 10 Cylinder Pilots, and 13 Handgun Bore Pilots. Flip-storage box with foam insert. MASTER SET - Includes one 90°, 45°, and 79° Cutter, one Handle, 17 rifle muzzle pilots, 10 revolver cylinder pilots, 5 Handgun Bore Pilots, 8 Rifle/Handgun muzzle pilots in a storage box with foam insert. Does not include .17 caliber pilots. .17 CALIBER MASTER SET - Includes one 90° and 45° Cutter, one Handle, and 3 rifle muzzle pilots in .165", .166", and .167" diameters for.17 centerfire and .17 rimfire calibers. Does not include 79° (11°) muzzle crowning cutter, available separately.
Select one of the following for other rifle/handgun muzzles, cylinder facing & chamfering tools.
Steel One Caliber Set | 45° Cutter & Steel Pilot | ||
Brass One Caliber Set | 45° Cutter & Brass Pilot | ||
90° Cutter & Steel Pilot | Steel Pilot Only | ||
90° Cutter & Brass Pilot | Brass Pilot Only |
Big Book Catalog, Issue:71, Page:458
Comments(0)
Leave a comments